Contact 
Spare remote controller TOUSEK RS433 TXR-2B (RS433 TXR2B) - 100% replacement for original remote controller.
The remote control has been specially developed for the following TOUSEK models: PULL T5, PULL T8, TURN 20. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)
- It is a fully-fledged spare remote controller, shown on the left (It is not „universal“).
- The remote controller is guaranteed for 2 years.
You will receive a remote controller ready to use. The only thing you have to do is register the remote controller to control unit of engine/drive.
We supply the remote control shown on the left.
Process of registering remote controller to main unit:
Common method:
- Open the control unit of the device where the remote control receiver is located. On the board or printed circuit of the receiver, there is a black/white button labeled as MEMO.
- Press this button and hold it for approximately 4 seconds, the receiver will start beeping with a continuous uninterrupted tone.
- Press the corresponding button (channel) on the new remote control that you want to use to operate the device.
- A broken beeping tone lasting about 2 seconds will be heard, indicating the synchronization of the receiver with the given button of the new remote control.
- Release the MEMO button, now press the newly synchronized button on the remote control. If the device responds (opens, closes), it is fine. If not, repeat the synchronization process.
Alternative method:
- Turn the already synchronized remote control to face its back towards you and use a paperclip to press the tuning button located under the hole in the cover. (Do not hold the button continuously and stand close to the tuned receiver).
- The receiver will start signaling the tuning with a continuous beeping tone.
- Press the button (channel) on the new remote control that you want to use to operate the device.
- A broken beeping tone lasting about 2 seconds will be heard, indicating that the receiver and the button on the remote control are synchronized.
- Now press the tuned button on the new remote control. If the device responds (opens, closes), it is fine. If not, repeat the tuning process.
This remote control is out of the stock now. Will be restocked within 5-10 days. For detailed information please contact us.
Spare remote controller TOUSEK RS433 TXR-2B (RS433 TXR2B) - 100% replacement for original remote controller.
The remote control has been specially developed for the following TOUSEK models: PULL T5, PULL T8, TURN 20. (There may not be listed all compatible models. If you are not sure, just tell us your device model (by online chat, email), we will promptly check, verify if compatible with your device. The verified compatibility is guaranteed by us.)
- It is a fully-fledged spare remote controller, shown on the left (It is not „universal“).
- The remote controller is guaranteed for 2 years.
You will receive a remote controller ready to use. The only thing you have to do is register the remote controller to control unit of engine/drive.
We supply the remote control shown on the left.
Process of registering remote controller to main unit:
Common method:
- Open the control unit of the device where the remote control receiver is located. On the board or printed circuit of the receiver, there is a black/white button labeled as MEMO.
- Press this button and hold it for approximately 4 seconds, the receiver will start beeping with a continuous uninterrupted tone.
- Press the corresponding button (channel) on the new remote control that you want to use to operate the device.
- A broken beeping tone lasting about 2 seconds will be heard, indicating the synchronization of the receiver with the given button of the new remote control.
- Release the MEMO button, now press the newly synchronized button on the remote control. If the device responds (opens, closes), it is fine. If not, repeat the synchronization process.
Alternative method:
- Turn the already synchronized remote control to face its back towards you and use a paperclip to press the tuning button located under the hole in the cover. (Do not hold the button continuously and stand close to the tuned receiver).
- The receiver will start signaling the tuning with a continuous beeping tone.
- Press the button (channel) on the new remote control that you want to use to operate the device.
- A broken beeping tone lasting about 2 seconds will be heard, indicating that the receiver and the button on the remote control are synchronized.
- Now press the tuned button on the new remote control. If the device responds (opens, closes), it is fine. If not, repeat the tuning process.
This remote control is out of the stock now. Will be restocked within 5-10 days. For detailed information please contact us.
Featured Products
Radio range extender for remote control IR signal integrated in the battery - UFON 433 MHz
General DUREMOTE 2 tailor made remote control with button printing on demand
General MAGIC - remote control for SMART TV with keyboard and air-mouse function
Share your device's brand and model, and we'll handle the rest. Our experts will handle the request and your tailored recommendations will be on their way via email.
